View PC900V0YIPXF_7743660.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

pc900v0nszxf series 1. recognized by ul1577 (double protection isolation), file no. e64380 (as model no. pc900v ) 2. approved by vde, din en60747-5-2 ( ? ) (as an option), file no. 40008189 (as model no. pc900v ) 3. package resin : ul flammability grade (94v-0) ( ? ) din en60747-5-2 : successor standard of din vde0884 features agency approvals/compliance 1. programmable controllers 2. pc peripherals 3. electronic musical instruments applications digital output, normal off operation dip 6 pin ? opic photocoupler 1. 6 pin dip package 2. double transfer mold package (ideal for flow soldering) 3. normal off operation, open collector output 4. ttl and lsttl compatible output 5. operating supply voltage (v cc : 3 to 15 v) 6. isolation voltage (v iso(rms) : 5.0 kv) 7. lead-free and rohs directive compliant description pc900v0nszxf series contains an ired optically coupled to an opic chip. it is packaged in a 6 pin dip, available in smt gullwing lead-form and wide smt gullwing lead-form option. input-output isolation voltage(rms) is 5.0kv. 1 sheet no.: d2-a05302en date jun. 30. 2005 ?sharp corporation notice the content of data sheet is subject to change without prior notice. in the absence of confirmation by device specification sheets, sharp takes no responsibility for any defects that may occur in equipment using any sharp devices shown in catalogs, data books, etc. contact sharp in order to obtain the latest device specification sheets before usin g any sharp device. pc900v0nszxf series ? "opic"(optical ic) is a trademark of the sharp corporation. an opic consists of a light-detecting element and a signal-processi ng circuit integrated onto a single chip.
internal connection diagram 1 2 3 4 5 6 anode cathode nc v cc v o gnd 6 5 4 1 2 3 voltage regulator amp 2 sheet no.: d2-a05302en outline dimensions (unit : mm) 1. through-hole [ex. pc900v0nszxf ] 2. through-hole (vde option) [ex. pc900v0yszxf ] 7.12 0.5 : 0 to 13? 7.62 0.3 epoxy resin 6.5 0.5 0.6 0.2 1.2 0.3 1 2 3 6 5 4 0.5 typ. 2.9 0.5 0.5 0.1 2.54 0.25 3.25 0.5 3.5 0.5 pc900v sharp mark "s" date code anode mark 7.12 0.5 : 0 to 13? 7.62 0.3 epoxy resin 6.5 0.5 0.6 0.2 1.2 0.3 1 2 3 6 5 4 0.5 typ. 2.9 0.5 0.5 0.1 2.54 0.25 3.25 0.5 3.5 0.5 vde identification mark pc900v anode mark date code sharp mark "s" 4 3. smt gullwing lead-form [ex. pc900v0nipxf ] 4. smt gullwing lead-form (vde option) [ex. PC900V0YIPXF ] pc900v0nszxf series 7.12 0.5 7.62 0.3 epoxy resin 6.5 0.5 0.6 0.2 1.2 0.3 2.54 0.25 3.5 0.5 0.35 0.25 1.0 + 0.4 ? 0 1.0 + 0.4 ? 0 10.0 + 0 ? 0.5 0.26 0.1 1 2 3 6 5 4 pc900v sharp mark "s" date code anode mark 7.12 0.5 7.62 0.3 epoxy resin 6.5 0.5 0.6 0.2 1.2 0.3 2.54 0.25 3.5 0.5 0.35 0.25 1.0 + 0.4 ? 0 1.0 + 0.4 ? 0 10.0 + 0 ? 0.5 0.26 0.1 1 2 3 6 5 4 pc900v anode mark date code sharp mark "s" vde identification mark 4 product mass : approx. 0.35g product mass : approx. 0.35g product mass : approx. 0.36g product mass : approx. 0.36g
3 sheet no.: d2-a05302en (unit : mm) 5. wide smt gullwing lead-form [ex. pc900v0nupxf ] 6. wide smt gullwing lead-form (vde option) [ex. pc900v0yupxf ] pc900v0nszxf series 7.12 0.5 7.62 0.3 epoxy resin 6.5 0.5 0.6 0.2 1.2 0.3 2.54 0.25 0.75 0.25 0.75 0.25 10.16 0.5 3.5 0.5 0.25 0.25 0.26 0.1 12.0 max. pc900v sharp mark "s" date code anode mark pc900v 7.12 0.5 7.62 0.3 epoxy resin 6.5 0.5 0.6 0.2 1.2 0.3 2.54 0.25 0.75 0.25 0.75 0.25 10.16 0.5 3.5 0.5 0.25 0.25 0.26 0.1 anode mark date code sharp mark "s" 12.0 max. 4 vde identification mark product mass : approx. 0.35g product mass : approx. 0.35g plating material : sncu (cu : typ. 2%)
date code (2 digit) a.d. 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 mark a b c d e f h j k l m n mark p r s t u v w x a b c mark 1 2 3 4 5 6 7 8 9 o n d month january february march april may june july august september october november december a.d 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2nd digit month of production 1st digit year of production 4 repeats in a 20 year cycle sheet no.: d2-a05302en pc900v0nszxf series country of origin japan rank mark there is no rank mark indicator.
sheet no.: d2-a05302en electro-optical characteristics parameter conditions forward voltage reverse current terminal capacitance low level output voltage transfer characteristics response time high level supply current "high low" input threshold current "low high" input threshold current isolation voltage hysteresis *4 *5 *6 "low high" propagation delay time "high low" propagation delay time rise time fall time min. 0.7 3 ? ? ? ? ? ? 5 10 10 ? 0.4 0.3 ? ? ? ? typ. 1.0 1.1 ? ? 30 0.2 1.0 ? ? 0.7 0.8 1.1 1 10 11 0.05 0.1 1 2 max. 1.4 10 250 15 0.4 5.0 2.0 4.0 ? ? 0.9 3 6 0.5 0.5 ? unit v a pf v v ma ma ma ? ? s symbol v f i r c t v cc i ccl i cch i fhl t f i flh i flh /i fhl r iso t phl t plh t r i f = 0.3ma i f = 4ma t a = 25?c, v r = 3v t a = 25?c, v = 0, f = 1khz t a = 25?c, v cc = 5v, r l = 280 ? operating supply voltage ? i ol = 16ma, v cc = 5v, i f = 4ma v cc = 5v, i f = 0 t a = 25?c, v cc = 5v, i f = 4ma r l = 280 ? v cc = 5v, r l = 280 ? t a = 25?c, v cc = 5v, r l = 280 ? t a = 25?c, dc500v, 40 to 60%rh v cc = 5v, r l = 280 ? v cc = 5v, r l = 280 ? (unless otherwise specified t a = 0 to + 70?c) *4 i fhl represents forward current when output goes from high to low. *5 i flh represents forward current when output goes from low to high. *6 hysteresis stands for i flh /i fhl . high level output current ? 0.5 ? 100 ? a v ol v o = v cc = 15v, i f = 0 low level supply current ? 2.5 5.0 ma i oh v cc = 5v, i f = 4ma input output absolute maximum ratings (t a = 25 ?c ) parameter symbol unit forward current ma *1 peak forward current a power dissipation mw supply voltage v high level output voltage v low level output current ma mw mw total power dissipation operating temperature storage temperature ?c isolation voltage ?c *2 *3 soldering temperature i f i fm p v cc v oh i ol p o p tot v iso (rms) t opr t stg t sol ?c *1 pulse width 100 s, duty ratio : 0.001 *2 40 to 60%rh, ac for 1minute , f=60hz *3 for 10s rating 50 1 reverse voltage power dissipation v v r 6 70 16 16 50 150 170 ? 25 to + 85 ? 40 to + 125 260 5.0 kv input output 5 pc900v0nszxf series
sheet no.: d2-a05302en model line-up pc900v0nszxf pc900v0yszxf ?????? approved pc900v0nupxf pc900v0yupxf lead form package model no. din en60747-5-2 sleeve through-hole 50pcs/ sleeve taping 50pcs/ sleeve smt gullwing wide smt gullwing ?????? approved pc900v0nizxf pc900v0nipxf ?????? pc900v0yizxf approved ?????? PC900V0YIPXF approved 6 please contact a local sharp sales representative to inquire about production status. pc900v0nszxf series
sheet no.: d2-a05302en 7 pc900v0nszxf series fig.1 test circuit for response time 5v 1.5v amp t r = t f = 0.01 s z o = 50 ? v in 47 ? 0.1 f v o 280 ? v in t phl t plh v oh 90% 10% t r v ol 50% v o voltage regulator t f 10 20 60 50 40 30 0 0 ? 25 25 50 75 100 85 ambient temperature t a (?c) forward current i f (ma) 50?c 25?c 0?c 0 1 10 100 0.5 1.0 1.5 2.0 2.5 3.0 ? 25?c forward voltage v f (v) forward current i f (ma) t a = 75?c 0 ? 25 100 025507 585 100 50 150 200 170 ambient temperature t a (?c) power dissipation p o , p tot (mw) p tot p o fig.3 power dissipation vs. ambient temperature fig.5 relative input threshold current vs. supply voltage fig.4 forward current vs. forward voltage fig.2 forward current vs. ambient temperature 0.2 0.4 0.6 1.4 510 01520 1.2 1.0 0.8 supply voltage v cc (v) relative input threshold current i fhl , i flh t a = 25?c i fhl = 1 at v cc = 5v i fhl i flh
sheet no.: d2-a05302en 8 pc900v0nszxf series fig.7 low level output voltage vs. low level output current fig.6 relative input threshold current vs. ambient temperature fig.9 supply current vs. supply voltage fig.11 rise time, fall time vs. load resistance fig.10 propagation delay time vs. forward current fig.8 low level output voltage vs. ambient temperature 0 1 2 9 517 113 5 4 3 6 7 8 11 15 79 3 25?c 85?c 25?c 85?c supply voltage v cc (v) supply current i cc (ma) t a = ? 25?c t a = ? 25?c i ccl { i cch { 0.2 0.4 relative input threshold current i fhl , i flh 0.6 0.8 1.6 0255075 ? 25 100 1.4 1.2 1 ambient temperature t a (?c) i fhl = 1 at t a = 25?c i flh i fhl v cc = 5v 0.01 1 0.1 1 10 100 low level output current i ol (ma) low level output voltage v ol (v) v cc = 5v t a = 25?c 0.2 0.3 0.5 0 ? 25 25 50 100 0.1 0 0.4 75 16ma 5ma low level output voltage v ol (v) ambient temperature t a (?c) v cc = 5v i ol = 30ma 0 0.1 0.1 0.2 0.3 0.4 0.5 110 load resistance r l (k ? ) t f t r rise time, fall time t r , t f ( s) v cc = 5v i f = 4ma t a = 25?c 0 1 2 3 4 5 10 20 30 40 60 050 forward current i f (ma) propagation delay time t phl , t plh ( s) v cc = 5v r l = 280 ? t a = 25?c t plh t phl remarks : please be aware that all data in the graph are just for reference and not for guarantee.
sheet no.: d2-a05302en 9 pc900v0nszxf series design considerations transistor of detector side in bipolar configuration may be damaged by static electricity due to its minute design. when handling these devices, general countermeasure against static electricity should be taken to avoid breakdown of devices or degradation of characteristics. notes about static electricity in order to stabilize power supply line, we should certainly recommend to connect a by-pass capacitor of 0.01 f or more between v cc and gnd near the device. the detector which is used in this device, has parasitic diode between each pins and gnd. there are cases that miss operation or destruction possibly may be occurred if electric potential of any pin becomes below gnd level even for instant. therefore it shall be recommended to design the circuit that electric potential of any pin does not become below gnd level. this product is not designed against irradiation and incorporates non-coherent ired. design guide degradation in general, the emission of the ired used in photocouplers will degrade over time. in the case of long term operation, please take the general ired degradation (50% degradation over 5 years) into the design consideration. please decide the input current which become 2 times of max. i fhl .
sheet no.: d2-a05302en ? for additional design assistance, please review our corresponding optoelectronic application notes. 10 pc900v0nszxf series recommended foot print (reference) 2.54 2.54 1.7 2.2 8.5 2.54 2.54 1.7 2.2 10.5 smt gullwing lead-form wide smt gullwing lead-form (unit : mm)
sheet no.: d2-a05302en manufacturing guidelines reflow soldering: reflow soldering should follow the temperature profile shown below. soldering should not exceed the curve of temperature profile and time. please don't solder more than twice. soldering method flow soldering : due to sharp's double transfer mold construction submersion in flow solder bath is allowed under the below listed guidelines. flow soldering should be completed below 270?c and within 10s. preheating is within the bounds of 100 to 150?c and 30 to 80s. please don't solder more than twice. hand soldering hand soldering should be completed within 3s when the point of solder iron is below 400?c. please don't solder more than twice. other notices please test the soldering method in actual condition and make sure the soldering works fine, since the impact on the junction between the device and pcb varies depending on the tooling and soldering conditions. 11 1234 300 200 100 0 0 (?c) terminal : 260?c peak ( package surface : 250?c peak) preheat 150 to 180?c, 120s or less reflow 220?c or more, 60s or less (min) pc900v0nszxf series
sheet no.: d2-a05302en solvent cleaning: solvent temperature should be 45?c or below immersion time should be 3 minutes or less ultrasonic cleaning: the impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time, size of pcb and mounting method of the device. therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of mass production. recommended solvent materials: ethyl alcohol, methyl alcohol and isopropyl alcohol in case the other type of solvent materials are intended to be used, please make sure they work fine in actual using conditions since some materials may erode the packaging resin. cleaning instructions this product shall not contain the following materials. and they are not used in the production process for this product. regulation substances : cfcs, halon, carbon tetrachloride, 1.1.1-trichloroethane (methylchloroform) specific brominated flame retardants such as the pbbos and pbbs are not used in this product at all. this product shall not contain the following materials banned in the rohs directive (2002/95/ec). ?ead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (pbb), polybrominated diphenyl ethers (pbde). presence of odc 12 pc900v0nszxf series
sheet no.: d2-a05302en 13 12.0 6.7 5.8 10.8 520 2 (unit : mm) pc900v0nszxf series package specification sleeve package package materials sleeve : hips (with anti-static material) stopper : styrene-elastomer package method max. 50 pcs. of products shall be packaged in a sleeve. both ends shall be closed by tabbed and tabless stoppers. the product shall be arranged in the sleeve with its anode mark on the tabless stopper side. max. 20 sleeves in one case. sleeve outline dimensions
sheet no.: d2-a05302en 14 tape and reel package 1. smt gullwing package materials carrier tape : a-pet (with anti-static material) cover tape : pet (three layer system) reel : ps carrier tape structure and dimensions f k e i d j b h h a c g 5? m ax. dimensions list (unit:mm) a 16.0 0.3 b 7.5 0.1 c 1.75 0.1 d 12.0 0.1 e 2.0 0.1 h 10.4 0.1 i 0.4 0.05 j 4.2 0.1 k 7.8 0.1 f 4.0 0.1 g 1.5 + 0.1 ? 0 a c e g f b d dimensions list (unit : mm) a 330 b 17.5 1.5 c 100 1.0 d 13 0.5 e 23 1.0 f 2.0 0.5 g 2.0 0.5 pull-out direction [packing : 1 000pcs/reel] reel structure and dimensions direction of product insertion pc900v0nszxf series
sheet no.: d2-a05302en 15 pc900v0nszxf series 2. wide smt gullwing package materials carrier tape : a-pet (with anti-static material) cover tape : pet (three layer system) reel : ps carrier tape structure and dimensions dimensions list a 24.0 0.3 b 11.5 0.1 c 1.75 0.1 d 12.0 0.1 e 2.0 0.1 h 12.2 0.1 i 0.4 0.05 j 4.1 0.1 k 7.6 0.1 f 4.0 0.1 g 1.5 + 0.1 ? 0 (unit : mm) j g i e c b a h h 5? max. f d k a c e g f b d dimensions list (unit : mm) a 330 b 25.5 1.5 c 100 1.0 d 13 0.5 e 23 1.0 f 2.0 0.5 g 2.0 0.5 pull-out direction [packing : 1 000pcs/reel] reel structure and dimensions direction of product insertion
?the circuit application examples in this publication are provided to explain representative applications of sharp devices and are not intended to guarantee any circuit design or license any intellectual property rights. sharp takes no responsibility for any problems rela- ted to any intellectual property right of a third party re- sulting from the use of sharp's devices. ?contact sharp in order to obtain the latest device specification sheets before using any sharp device. sharp reserves the right to make changes in the spec- ifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. manufac- turing locations are also subject to change without no- tice. ?observe the following points when using any devices in this publication. sharp takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) the devices in this publication are designed for use in general electronic equipment designs such as: --- personal computers --- office automation equipment --- telecommunication equipment [terminal] --- test and measurement equipment --- industrial control --- audio visual equipment --- consumer electronics (ii) measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when sharp devices are used for or in connection with equipment that requires higher reliability such as: - -- transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- traffic signals --- gas leakage sensor breakers --- alarm equipment --- various safety devices, etc. (iii) sharp devices shall not be used for or in connec- tion with equipment that requires an extremely high lev- el of reliability and safety such as: --- space applications --- telecommunication equipment [trunk lines] --- nuclear power control equipment - -- medical and other life support equipment (e.g., scuba). ?if the sharp devices listed in this publication fall with- in the scope of strategic products described in the for- eign exchange and foreign trade law of japan, it is necessary to obtain approval to export such sharp de- vices. ?this publication is the proprietary product of sharp and is copyrighted, with all rights reserved. under the copyright laws, no part of this publication may be repro- duced or transmitted in any form or by any means, elec- tronic or mechanical, for any purpose, in whole or in part, without the express written permission of sharp. express written permission is also required before any use of this publication may be made by a third party. ?contact and consult with a sharp representative if there are any questions about the contents of this pub- lication. 16 sheet no.: d2-a05302en important notices pc900v0nszxf series [e225]

▲Up To Search▲

Price & Availability of PC900V0YIPXF

	To Download PC900V0YIPXF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .